Tp link mr3020 openwrt


  • How to setup OpenWrt extroot, rootfs on USB storage
  • OpenWrt 19.07.4 arrives with greater support, improvements in web interface and more
  • TP-Link TL-MR3020 as AirPlay receiver
  • PirateBox creation based on TP-Link MR3020
  • OpenWRT on TP-Link MR3020 as infopoint with local webserver
  • Cara Install OpenWrt Pulpstone TP Link MR3020 Exroot
  • How to setup OpenWrt extroot, rootfs on USB storage

    Check this for instructions how to do this. Installing necessary packages Next we need to install drivers for a USB flash drive, filesystem and extroot. I used a 8 GB drive but 4 GB is fine as well. Make sure the flash drive is formated with ext4. Some USB flash drives might cause trouble. Configure exroot Alright, time to configure the flash drive as our root partition with extroot.

    This is also a nice failsafe if you manage the break the install or lock yourself out from the device somehow. If that occur you can boot the MR without the flash drive and just redo the steps above.

    Or you can use dd or similar on another system to create an image of your flash drive! Now, reboot your device and SSH into it once again. Running df should confirm that you now have plenty of space to use. Configuring the network The idea is to create a wireless guest network on the MR and provide internet access through it. The internet access will be received through its ethernet port from my laptop running Linux. This will create the subnet Now, time to configure the network in the MR SSH back to the device and do the following configurations.

    Although do note that some of your settings might be different and some will be, like your macaddr and such. But it should be pretty straightforward. To allow access to the internet we need to perform some actions on the Linux laptop. We need to add a route to the guest network and use iptables to NAT. Now, replace if needed wlp3s0 with your laptops wireless interface and enp0s25 with your ethernet interface.

    OpenWrt 19.07.4 arrives with greater support, improvements in web interface and more

    I assume it is better to start directly with a large drive and as much as possible a small in terms of physical dimension stick. The installation process try to connect to that site and when down as in my case , it can create some trouble. To proceed the installation I followed the perfect tutorial found here in french as it is my native language.

    This tutorial seems also interesting and better. Be careful, this did not work correctly for me, so here is what I think we must do, based on the modification I had to do after: Follow steps 1 to 8 concerning the openwrt installation and password setting. Change network configuration : config interface 'loopback' option ifname 'lo' option proto 'static' option ipaddr ' Change the firewall settings as indicated in the step 11 in the tutorial 4.

    Do not proceed this : Install missing packages opkg update opkg upgrade luci 5. Do not proceed this : At this step you should be able to see a web page typing the Ip adress in your browser 7. Install USB modules opkg update opkg install kmod-usb-uhci insmod usbcore insmod uhci opkg update opkg install kmod-usb-ohci insmod usb-ohci 8.

    Insert the Fat32 formated USB stick 9. Using another IP would make the PirateBox not working. In case you need to reinstall your PirateBox I had to re-flash my PirateBox due to some trouble during installation related to the non accessibility for the daviddarts website. To proceed this reinstallation of the OpenWrt Firmware, it is not still possible to use the integrated web interface.

    TP-Link TL-MR3020 as AirPlay receiver

    Configure exroot Alright, time to configure the flash drive as our root partition with extroot. This is also a nice failsafe if you manage the break the install or lock yourself out from the device somehow.

    PirateBox creation based on TP-Link MR3020

    If that occur you can boot the MR without the flash drive and just redo the steps above. Or you can use dd or similar on another system to create an image of your flash drive! Now, reboot your device and SSH into it once again. Running df should confirm that you now have plenty of space to use. Configuring the network The idea is to create a wireless guest network on the MR and provide internet access through it.

    OpenWRT on TP-Link MR3020 as infopoint with local webserver

    The internet access will be received through its ethernet port from my laptop running Linux. This will create the subnet Now, time to configure the network in the MR I assume it is better to start directly with a large drive and as much as possible a small in terms of physical dimension stick. The installation process try to connect to that site and when down as in my caseit can create some trouble.

    To proceed the installation I followed the perfect tutorial found here in french as it is my native language.

    Cara Install OpenWrt Pulpstone TP Link MR3020 Exroot

    This tutorial seems also interesting and better. Be careful, this did not work correctly for me, so here is what I think we must do, based on the modification I had to do after: Follow steps 1 to 8 concerning the openwrt installation and password setting.

    Change network configuration : config interface 'loopback' option ifname 'lo' option proto 'static' option ipaddr ' Change the firewall settings as indicated in the step 11 in the tutorial 4.


    Tp link mr3020 openwrt